Still, always worth checking the filter first, especially if you want to avoid bigger headaches later.
That makes sense, but I sometimes wonder—does anyone actually go straight for the reset before checking the filter? I get that the reset can clear a board glitch, but in my experience, 9 times out of 10 it’s just some random bit of junk stuck in there causing all the drama. I pulled out a hair tie once and felt like a detective solving the case.
Has anyone here had a spin issue that turned out to be something totally unexpected, not filter or board related? Like, could it be the drain hose or maybe even the belt slipping? Just curious how often it’s something less obvious.
Spin Cycle Surprises: When It’s Not the Obvious Stuff
I get that the reset can clear a board glitch, but in my experience, 9 times out of 10 it’s just some random bit of junk stuck in there causing all the drama.
That’s definitely been my experience too, but I’ve learned (the hard way) not to rule out the less obvious stuff—especially if you’re trying to avoid a costly repair down the line. I’m pretty cautious about anything involving moving parts or water, so I tend to look for the “hidden” issues if the filter looks clean.
One time, my washer just stopped spinning mid-cycle. Filter was spotless, no error code, and a reset did nothing. Turns out, the drain hose had a kink behind the machine from when a delivery guy pushed it back too far. The pump couldn’t force water out fast enough, so the machine wouldn’t spin. I only figured it out after pulling everything apart and double-checking all the connections. Not exactly how I wanted to spend my Sunday afternoon.
As for the belt, that’s another sneaky culprit. If it’s slipping or worn, you might notice a sort of burnt rubber smell or hear some weird noises before the spin cycle gives up completely. It’s not always easy to spot unless you’re comfortable opening up panels, but catching it early can save you from a total breakdown.
I get why folks go straight to the filter—it’s quick and usually solves it. But sometimes those “random” issues are hiding in plain sight. Personally, I’d rather spend an extra few minutes checking hoses or listening for odd sounds than risk a bigger repair bill later on. Even if it feels like overkill, just being thorough gives me peace of mind... and keeps my wallet happier in the long run.
Guess it just depends how much time (and patience) you’ve got when things go sideways.
I get why folks go straight to the filter—it’s quick and usually solves it. But sometimes those “random” issues are hiding in plain sight.
That’s spot on—sometimes it’s the stuff you can’t see right away that trips you up. I’ve been burned by assuming it was just a clogged filter, only to find out later the lid switch was acting up. It’s easy to forget how many safety interlocks these machines have now. If the lid sensor is even a little off, the washer might refuse to spin, no matter how clean everything else looks.
Here’s how I usually tackle it:
1. Unplug and reset—just in case it’s a board hiccup.
2. Check the filter and drain pump for obvious blockages.
3. Inspect hoses for kinks or pinches (like you mentioned—those can be sneaky).
4. Listen for weird noises during drain/spin cycles.
5. Test the lid switch or door lock if nothing else pans out.
Curious if anyone else has run into issues with those sensors? Sometimes I wonder if they’re more trouble than they’re worth...
Honestly, I get the frustration with all the sensors, but I’ve actually found them pretty helpful more often than not. Had a washer that wouldn’t spin, and it turned out the sensor was just doing its job—lid wasn’t closing all the way because of a rogue sock wedged in the hinge. If I’d skipped straight to the filter, I’d have missed it. Sometimes those “annoying” safety features save you from bigger headaches down the line... even if they do make troubleshooting a bit more of a puzzle.
Yeah, I get that. Sensors can be a pain, but they do catch stuff you’d never think to check. I had a similar thing—washer wouldn’t start, and it was just the door sensor not clicking in because of lint buildup. Still, sometimes I wish there was a quick way to tell if it’s a real problem or just the machine being picky. Guess it’s all part of the fun... or frustration.
